2014 Forest River Flagstaff MAC / LTD 206LTD Reviews, Prices, Specifications and Photos. Read all the latest Forest River Flagstaff MAC / LTD 206LTD information and Build-Your-Own RV on RV Guide's Trailer section.

The Flagstaff line is made up of four different series as of this writing, including:

  • Mac Series
  • Classic Series
  • High Wall Series
  • Hard Side Series

Each series has a few features to differentiate itself along with a common set of standard features and optional equipment.

Forest River Mac Series Specifications

Closed LengthOpen lengthTravel HeightBox LengthGVWR (lbs)Dry Hitch Weight (lbs)176LTD12' 0'17' 1'4' 8'8'2,14819020515' 3'20' 1'4' 9'10'2,876240206LTD14' 0'20' 1'4' 8'10'2,274174206ST17' 1'20' 4'4' 9'10'2,99524520720' 1'15' 3'4' 9'10'2,78625220820' 1'15' 3'4' 9'10'2,768

2014 Flagstaff Mac Pop Up Camper Manual Pdf

21922723' 10'2014 Flagstaff Mac Pop Up Camper Manual17' 2'4' 9'12'3,04329322823' 10'17' 2'4' 9'12'3,081331228BH23' 10'18' 8'4' 9'12'3,132382228D23' 10'17' 2'4' 9'

2014 Flagstaff Mac Pop Up Camper Manual Cranking

12'3,063313246D25' 10'19' 2'4' 9'14'3,249249BR23SC26' 5'21' 9'5' 2.5'12'3,810310BR28TSC30' 8'26' 0'5' 2.5'12'5,579219

Sample Mac Series Floor Plan

CamperMac Series 207 floor plan. Courtesy Forest River RV.

Flagstaff Mac Series

Forest River’s Flagstaff Mac series is a line of pop up tent trailers designed for budget-minded campers. The line comes equipped with certain basic features across more than a dozen different models that it contains, while offering a laundry list of optional equipment that you can add if you so desire.

The Mac series ranges in length from 12 feet to a bit over 21 feet in closed lengths and includes models with 10′, 12′ and 14′ boxes. Dry weights range from roughly 1,732 lbs. to nearly 3,000 lbs., so they are all on the heavier side.

Standard Features and Optional Equipment

Some of the standard features that the Mac series offers include:

  • Swing level galley
  • Three burner range
  • Ice box
  • Dinette
  • Cable hookups
  • 35 Amp converter and charger
  • LED lighting
  • 20 gallon fresh water tank

Features includes in select models include:

  • Storage deck
  • Toylok locking system
  • Diamond plated front, rear and side skirt

Some of the optional equipment you can choose from includes:

  • Bike rack
  • Power lift system
  • Dual propane bottles
  • Reinforced a/c vent

Lift-system troubleshooting

Flagstaff's lift-system is one of the easiest to operate and maintain of any pop-up camper. In fact, the lift-system can operate for years without any maintenance at all. However, lift-systems have parts and--even though salespeople don't like to admit it--parts can wear down or break.

Here are some tips to keep the camper popping up and down for years to come.

The lift-system cranks harder than usual

First check for any obstructions including an unlatched roof latch or gear loaded on a roof rack (all items stored on a roof rack should be removed before raising a pop-up roof). If that's not the issue it's possible the lift system needs a tune-up.

Lift-system tune-up
2014 Flagstaff Mac Pop Up Camper Manual

For all push-spring/cable-drive systems:

  1. Locate the weep holes on the lifter conduit at each corner of the camper (under the camper).
  2. Use an oil can to pump a small amount of oil (motor oil works fine) into the conduit. This reduces the friction of the push-spring against the conduit. (Use a rag or paper towel to seal the connection between the oil can and the weep hole.)
  3. Use a piece of plumber's putty, strip caulking, chewed bubble gum and duct tape, etc. to plug the hole temporarily so the oil can saturate the push-spring and not just drip back out of the hole. Remember to remove this plug after a few hours. A small amount of oil will still be able to drip from the weep hole so have some cardboard or a drip pan handy.

For hand-crank lift-systems:

  1. On the winch: spray lubricant (like WD-40) around the winch's main bushing and the main drum (where the cable spools). Be careful to avoid the leather disc--this enables the winch to hold the roof in position when you stop cranking and needs to be dry to work.

For power-lift systems:

  1. On the winch: remove the lower pan (the cover that prevents mud and road junk from hitting the winch) and spray lubricant (like WD-40) around the main drum (where the cable spools).

Step 5 (not usually necessary but good to know): paraffin wax (available at grocery stores in the canning section) can be rubbed on the lifter arms if the lifter arm sticks when the roof is lowered. Another cause of the roof sticking is the camper not being level. Make sure the camper is level and see if the lifter arm still sticks during tear-down before attempting the tedious task of waxing the lifter arms.

One or two corners of the roof stay up when I crank down the roof

This is probably due to a not-level-enough camper. If the camper is leaning to one side or the other the roof puts extra pressure on that side's lifter arms. The extra pressure creates friction which may be sufficient to hold the roof up even when you crank down the lift-system.

Slow solution: crank the roof up and level the camper better. Try cranking down the roof again.

Fast solution: push on the lifter arm (as close to the roof as you can reach without losing your leverage) away from the direction the roof is leaning. This will take the pressure off the lifter arm.

If the lift-system is cranked down (there is slack on the lift system when the roof hung up on the lifter arm) when you try this the roof could fall rapidly and pinch you fingers in the lifter arm sections or hit someone in the head with the falling roof! We recommend trying this method only if the roof has been cranked down a foot or so to limit the falling action of the roof. If you didn't notice the lifter arms hanging up until the other side is down much further, crank the roof back up until the loose side is only a foot or so below the stuck side.

The crank flops around in the winch socket making it tough to crank

The square winch socket the crank slides into is replaceable. It can also be repaired by hammering the socket back into it's original square shape (but this generally requires more labor than what the new socket costs).

April 2015: The following section refers to Carefree of Colorado's older power winch, model P55000. Flagstaff now uses Carefree's model P55012 for campers with a powered lift-system.

The powered lift-system won't work (motor won't turn on)

  1. Make sure the battery has power.
  2. Make sure the thick red wire coming from the powered lift-system is connected to the battery's positive terminal; make sure the thick black wire is connected to the battery's negative terminal.
  3. Check that the switch connections are tight.

If these three items look good but still no power goes to the motor the internal fuse in the winch system may be blown. To access this fuse:

  1. Remove the lower pan/cover from the tongue (the pan is held by four screws with a 3/8' hex head).
  2. Locate the big wad of electrical tape where several wires come together.
  3. Unwrap that big wad of electrical tape to reveal the large-amp fuse (50 or 60AMP, depending on the model year).
  4. The fuse connects to the wires by nut and bolt--use wrenches or nutdrivers to remove/replace the fuse (keep track of which wires attached to which end of the fuse).


(This view is from the top but the fuse is easier to get to from the bottom)

If this does not cure the problem check that the limit-switches are functional (as described in the next section ). If the limit switches are functional it's possible the motor is a goner.

April 2015: The following section refers to Carefree of Colorado's older power winch, model P55000. Flagstaff now uses Carefree's model P55012 for campers with a powered lift-system.

The powered lift-system won't raise the roof all the way (limit-switch issues)

The powered winch has limit switches on the high end and the low end to make sure the winch doesn't crank the cable up or down too far.

Ideally the limit switch will be set by the dealer before you receive the camper but even so, over time, the cable can stretch slightly or the cable can spool on the winch drum in such a way that the limit switch becomes an issue.

To adjust the high limit switch:

  1. Remove the cover (black plastic cowling) from the top of the lift-system area. The cover has the switch attached to it so you can only move the cover off to the side as far as the wires will reach.
  2. The bolt has a lock nut that needs to be loosened before the bolt can be moved in or out, depending on whether the roof needs to go higher or lower before stopping. This is a trial-and-error affair--be patient and eventually the roof will stop exactly where you want it to (typically when the height-indicator cable becomes taut).

To adjust the low limit-switch:

  1. Remove the cover (black plastic cowling) from the top of the lift-system area. The cover has the switch attached to it so you can only move the cover off to the side as far as the wires will reach.
  2. Move the low-limit screw in or out, depending on when you want the winch to stop cranking down. Ideally the winch would stop after giving plenty of slack on the lift cable such that the roof can be pushed down and latched without tension/pressure from the lift cable.

NOTE: the wires connecting the limit switch assemblies to the system can jiggle loose over time. Use a Phillips screwdriver to tighten the connections.

April 2015: The following section refers to Carefree of Colorado's older power winch, model P55000. Flagstaff now uses Carefree's model P55012 for campers with a powered lift-system.

Powered lift-system back-up

If the battery is dead:

Hook up your tow vehicle's battery to the camper's battery with jumper cables (or hook-up your wire loom if you have a charging circuit). Let the car battery do the lifting until the camper's battery is able to be recharged.

If the battery is full but the motor just will not work for some reason:

Pop the round plastic plug from the black plastic cowling (the cover the switch is attached to). Under the plug is a big wad of grease (see picture in previous section ). In the middle of the wad of grease is a bolt head that runs the worm drive to lift the roof manually.

Flagstaff provides a hand crank for this back-up drive. You would NEVER want to use this crank, at least by hand. Here's why:

The power-lift system is geared such that a relatively modest electric motor can lift a 200-300lb. camper roof. This is perfect for a fast-spinning motor; this is a nightmare for a person using a hand crank. It takes roughly 2000 turns with the back-up crank to lift the camper roof by hand! So, while the electric motor can raise the roof in roughly 30 seconds it would take most of us ~30 hours to raise the roof by hand.

The MUCH better solution involves using a cordless drill and a socket that will do the cranking for you. In fact, the first thing we would do with our own powered lift-system back-up crank is chop off the handle in a band saw and keep the end for use in a cordless drill.

2014 Flagstaff Mac Pop Up Camper Manual Pdf

Our band saw is available from 7:30-5:30 Mon-Sat...

Can I exchange my manual winch for a powered one?

Yes. Powered lift-system in Options

Can I exchange my powered winch for a manual one?

Yes. Manual winch in Parts

The preceding information regards the current Flagstaff lift system. For the chain-drive system used from 1988 to 199(5?) please call us at 303-922-6221.

Back to Troubleshooting

Back to Articles & Tutorials

Privacy © 2009-2019 Roberts Sales. All rights reserved.

⇐ ⇐ Mcculloch Power Mac 320 Manual
⇒ ⇒ Manual Slow Down Mac Fan